| Both sides previous revision Previous revision Next revision | Previous revision |
| 3dprinting:ender3pro [2024/04/26 17:37] – jon | 3dprinting:ender3pro [2025/04/01 15:14] (current) – jon |
|---|
| ====== Ender 3 Pro ====== | ====== Ender 3 Pro/ Ender 3 v2 ====== |
| |
| As part of MicroCenter's coupon deal in exchange for your personal data (fake email and phone #), I picked this printer up for $100 plus tax. The assembly was not bad once you understood the meaning behind the order of operations. What you do initially in the beginning of the setup ultimately effects the whole build, so a lot of caution is needed to ensure the frame is square, and that you're assembling it on a level, and flat surface. | As part of MicroCenter's coupon deal in exchange for your personal data (fake email and phone #), I picked this printer up for $100 plus tax. The assembly was not bad once you understood the meaning behind the order of operations. What you do initially in the beginning of the setup ultimately effects the whole build, so a lot of caution is needed to ensure the frame is square, and that you're assembling it on a level, and flat surface. |
| |
| ===== Calibrations ===== | ===== Calibrations ===== |
| | |
| | https://www.reddit.com/r/ender3v2/s/q2FU6IXtI3 |
| |
| Part 1 - https://docs.google.com/document/d/1fxALEbcOqGYnBigPfioxTBZBQMxrY56HyCoimZ5VTf8 | Part 1 - https://docs.google.com/document/d/1fxALEbcOqGYnBigPfioxTBZBQMxrY56HyCoimZ5VTf8 |
| Part 2 - https://docs.google.com/document/d/1YG6HLjqtQQwEa0YvdKQx-v0PVRt5OBRjw5jKOw5HK4s | Part 2 - https://docs.google.com/document/d/1YG6HLjqtQQwEa0YvdKQx-v0PVRt5OBRjw5jKOw5HK4s |
| | |
| | Teaching Tech is the backbone for most of this - https://teachingtechyt.github.io/calibration.html |
| | |
| | MRISCOC overview - https://github.com/mriscoc/Ender3V2S1/wiki/Calibration-Guides |
| | |
| | A nice video overview from someone grabbing their faves from TT and Ellis - https://www.youtube.com/watch?v=rSCwTtJdzo0 |
| | |
| | ==== Linear Advance/Pressure Advance ==== |
| | |
| | Perhaps the biggest thing you need to calibrate for is Linear Advance/Pressure Advance. In Marlin, this needs to be enabled. For Enders, this means, a custom compile. If using mriscoc firmware, this also needs a special version that's not on the main release page, but thankfully it is pre-compiled. |
| | |
| | MRISCOC docs - https://github.com/mriscoc/Ender3V2S1/wiki/Linear-Advance-(LA) |
| | |
| | This is covered in the Ellis3dp and Teaching Tech guides, but it will allow you to not have to spend as much time fudging with the other settings to get a print dialed in. |
| | |
| | Perfect first layer prints - https://www.printables.com/model/213992-perfect-1st-layers-ender-3-v2-ender-3s1-ender-3s1-/comments |
| | |
| |
| ==== Retraction Tests ==== | ==== Retraction Tests ==== |
| * https://all3dp.com/2/octoprint-bed-level-visualizer-guide/ | * https://all3dp.com/2/octoprint-bed-level-visualizer-guide/ |
| * https://community.octoprint.org/t/put-tape-on-the-5v-pin-why-and-how/13574 | * https://community.octoprint.org/t/put-tape-on-the-5v-pin-why-and-how/13574 |
| | * https://print.piffa.net/ |